PRESENTING IN FRENCH LANGUAGE, BELT FASTENING CLIPS INSTALLATION GUIDE.

HIC Conveyor Belts-Fasteners Installation

Courroies transporteuses en caoutchouc PVC textile plis pour le transport de marchandises, les convoyeurs moteur solide ceinture de fixation des plaques d'acier-charnières Choix Installation être fait correctement utilisé pour la manutention des matériaux en vrac dans les aéroports, les entrepôts, les industries des mines pour obtenir une longue durée de vie.

Conveyor Belts Méthode d'installation et de l'information

Poulie 400mm Taille de la tête et la queue min 315mm être utilisée jusqu'à une épaisseur de 5,5 mm intérieur 3/4ply ceinture et pas moins de min. diamètre suggestions couches de séparation et d'autre dérapage problème peut se produire.
Matériaux de construction-up sur les poulies et les rouleaux doivent être enlevés de temps en temps pour éviter les dommages et ceinture de désalignement.
Endlessing être fait en forme de V en utilisant vulcanisation à chaud composé rejoint carrément, d'autre ceinture se déroulera d'un côté ou de off-center. Utiliser seulement sur les éléments de fixation 25% plus de force de ceinture, sinon la vie permettra de réduire
L'eau d'arrosage pour les RH grade ceintures (en utilisant épaisse couverture) se fait à la poulie de queue pour une meilleure vie et ne jamais cesser de ceinture chargée de MATL chaud.
Même si la production sans taches ou plaques sont visibles à la fois, rien d'intervenir performance. De même, les rides ne sont également pas couche intérieure de tissu utilisé, mais doublure en tissu et du papier cellophane impression des marques de ceinture de guérir la presse, peut être laissé sans surveillance.
Les bords sont coupés pour MFD NN & EP et moulé type de tissu de coton.
Joints couches en tissu sont utilisés à certains moments de la force en général plus élevés.
Evaluation de ceinture en tissu de nylon 3ply min. (Type315 / 3) jusqu'à 800 kg/m3 de densité de matière en vrac max. Ceinture de largeur et 800 mm min. 4ply NN (strength630 / 4 kN / m) pour upto1500kg/m3 mbd max. 1200mmW être utilisé si la capacité de charge, vitesse, etc facteurs soient pris en considération.
Degré de couverture avec M24 min. haut en bas de 3 mm et 1,5 mm pour les matériaux abrasifs, de matériaux chauds> 65C upto120C temp 4x2mm min BLAZE (HR) et de MATL jusqu'à 150C 6x2.5mm min. BETAPLUS (SHR) est utilisé.
Taille Variation (+ 1,5% Largeur; +, -10% d'épaisseur, 5%, -1% Longueur), comme par mfg tolérances acceptables.

How to Install Belt At a Glance

Once the roll of belting has been transported to the point of installation, it should be mounted on a suitable shaft for unrolling and threading onto the conveyor. Conveyor belting is normally rolled at the factory with the carrying side out.

Consequently, in mounting the roll the belt must lead off the top of the roll if it is being pulled onto the troughing or carrying idlers, but it must lead off the bottom of the roll if it is being pulled onto the return idlers. When pulling the belt onto the conveyor or radial stacker, the roll will turn opposite the direction indicated by the arrows on the crate. The drawing bellows illustrates a suitable method of mounting as well as leading off the top of the roll for pulling onto the troughing idlers.

In some cases, such as in mines, where head room does not permit maneuvering a roll, the belt may have to be pulled off the roll and re-fed. Extreme care should be exercised to see that the loops have large bends to avoid kinking or placing undue strain on the belt, and no weight should ever be placed on the belt when it is in this position. Another method of handling belting under such conditions is to lay the roll on a turntable with a vertical spindle.

Rubber Belt Roll Handling Method

Reels or rolls should never be dropped from a freight car, truck, or other means of conveyance since their weight will break the packaging and may damage the belt. Reels or rolls should always be rolled or provisions should be made for hoisting them. For hoisting, a bar is passed through the hole in the center of the roll. Chains or cables looped around the bar ends should be provided with a spreader above the roll to avoid damage to the belt edges.

HIC la coopération internationale de la marque de qualité UNIVERSAL Fabriqué en caoutchouc et textile combiner Conveyor Belts remplaçant IS 1891, DIN 22102, ISO 4195 & High Temperature Abrasion Resistant aspect Advantage assure Long Life Reliability.

Full Width Cleats

Super Heat Resistant

Non-Abrasive M

Hygienic Food

Merci pour votre achat de produits et de convoyeur UNIVERSAL Wish You Safe Materials Mouvement.

Useful Links

HIC Conveyor Belts-Fasteners Installation

Industries of Uttar Pradesh, Assam, Rajasthan, Madhya Pradesh, Meghalaya, Punjab, Uttaranchal-India: Asia using conveyor belts and belting hinges-fasteners to transport bulk materials; airports, warehouses and mining industries selection Installation guide to get long life from materials handling belt conveyor systems.

Conveyor Belts Installation Method & Information

Pulley Size of head 400mm & tail 315mm min be used upto 5.5mm inner thickness of 3/4ply belt and not less than min. diameter suggestions else ply separation & slippage problem can happen.
Materials Build-up on pulleys & idlers should be removed periodically to avoid belt damage & misalignment.
Endlessing be done in V-shaped using Hot Vulcanizing compound joined squarely, else belt will run to one side or off-center. Use fasteners only on 25% more strength belt,else life will reduce
Water Sprinkling for HR grade belts (using thicker cover) be done at tail pulley for better life & never stop belt loaded with hot matl.
Unhampered Production even if Blemishes or patches are visible at times, nothing to interfere performance. Similarly, Wrinkles are also not inner ply fabric used but liner cloth & cellophane paper impression marks of belt curing press, be left unattended.
Edges mfd are Cut for NN&EP fabric and moulded type for Cotton.
Joints in fabric ply at times are used of usually higher strength.
Belt Rating of 3ply Nylon fabric min.(type315/3) upto 800 kg/m3 material bulk density for max. 800mm belt width & min. 4ply NN (strength630/4 KN/m)upto1500kg/m3 mbd for max. 1200mmW be used though carrying capacity, speed, etc factors be considered.
Cover Grade of M24 with min. top 3mm & 1.5mm bottom for abrasive materials, for hot materials >65C upto120C temp 4x2mm min BLAZE (HR) & for matl upto 150C 6x2.5mm min. BETAPLUS(SHR) be used.
Size Variation (+, -1.5% Width; +, -10% Thickness;+5%,-1% Length) as per mfg tolerances should be acceptable.

Thank You For Purchasing UNIVERSAL Conveyor Product & Wish You Safe Materials Movement.

HIC International Co’s Manufactured UNIVERSAL Brand Quality rubber & textile combine Conveyor Belts superseding IS 1891, DIN 22102, ISO 4195 High Abrasion & Temperature Resistant aspect Advantage assures Long Life Reliability.

Disclaimer: Information’s, written and verbal are provided by HIC, relative to its products which it determines to be reliable & no liabilities of whatsoever nature in regards to its uses. The purchaser of UNIVERSAL brand industrial products should determine for itself the suitability of such products.